| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This is managed by the backend and should be read-only for PDs.
|
|
|
|
|
|
|
|
Move initialization code of protocol decoders from the constructor to a
new reset() helper method. The libsigrokdecode backend could run this
method several times to clear the decoder's internal state, before new
data from another acquisition gets fed to decode() calls.
|
|
Telling .wait() to "skip one sample" slightly obfuscates the intent of
getting the next samples while no condition applies. Explicitly pass no
condition arguments instead, to better reflect the purpose. Coincidently
these .wait() calls will execute in slightly less expensive code paths
in the common code.
|
|
Rephrase how the 'WAIT IDLE' stage skips over all-low input signals.
Have the next high level on either line detected in common code.
|
|
|
|
Remove the FSF postal address as it might change (it did in the past).
Reference the gnu.org website instead which is more stable.
|
|
|
|
PID decoding is normally done in the packet layer, but the signalling
layer has to switch behaviour on detection of an PREamble PID.
|
|
|
|
If the oldsym is not set to 'J' before entering IDLE state, the SOP
detection will never trigger
|
|
In automatic mode, the bus is assumed to be in IDLE state. After a
RESET, the bus state is checked again.
|
|
Resets are at least 10ms at the root hub downstream facing port and
2.5us at the device (root hub reset may be shortened by itermediate
hubs).
Keep-alive is a low-speed only signalling condition, as low-speed has no
SOFs to inhibit devices to enter suspend
|
|
Instead of centering the block around the sampleposition, which shows
some visual glitches due to rounding, use the edge positions already
known. Remove unused halfbit symbol.
|
|
Only SE0 and J are valid symbols during EOP
|
|
Do not call get_eop() from get_bit(), but directly issue the symbol. As
get_eop() is only called during the GET EOP state, the SE0 is implicit and
there is no need to save it into the syms array.
|
|
|
|
More than six consecutive 1's are an error
|
|
No need to replicate the symbol formatting in several places
|
|
|
|
USB low/full speed allows for frequency tolerance of 1.5%/0.25%. At
maximum packet size (sync + PID + data + CRC16) of 12 bytes/1027 bytes
this amounts to 1.4 bits/20 bits, so the decoder has to lock to the
actual symbol frequency to avoid any symbol misdetections.
The signal is sampled twice, once at the symbol center and once at
the expected edge position. Comparing the symbol at both positions gives
an indication if the current bit width is too low or too high. Adjust
accordingly.
|
|
Anything else in the pd.py files doesn't have to be imported/exposed.
|
|
Drop them from the libsigrokdecode repository.
|
|
|
|
- No newlines at the end of files.
- No trailing ';' characters.
- Comparison with None: Use 'is None' or 'is not None'.
- Comparison with True/False: Use 'if cond:' or 'if not cond:'.
- Various minor whitespace fixes.
|
|
Also, use the "if not self.samplerate" form, which catches both the case
where self.samplerate is None, as well as the case where it is 0.
|
|
In all current PDs it is not necessary to raise an exception upon
invalid states (of the PD's state machine), since we can guarantee that
no such invalid state can ever be reached in these PDs.
|
|
Older libsigrokdecode versions are no longer able to use the current
versions of the PDs (various changes in syntax etc).
|
|
Variables of type 'struct srd_channel *' are consistently named 'pdch' to
make them easily distinguishable from libsigrok's 'struct sr_channel *'
variables that are consistently named 'ch'.
|
|
|
|
|
|
Annotation entries also consist of a tuple, not a list.
|
|
|
|
Each option consists of a dictionary with the following keys:
id The option id, which is passed in when setting a value.
desc A description of the option, suitable for display.
def The default value for this option.
values (optional) If present, a tuple containing values the option
may take. They must be of the same type as the default.
Valid types for the options are UTF-8-encoded strings, integers, and
floating point values.
|
|
|
|
The output type is now called OUTPUT_PYTHON, adapt all PDs to that.
|
|
The single comment re-stating the PD's name / description / purpose in
each pd.py file is not really needed, that info is available in the
Decoder class' attributes already.
|
|
|
|
This automatically figures out the files to install for each protocol
decoder, without involving autotools.
All python files (filenames ending in .py) are always installed. If a
protocol decoder requires installation of a non-python file, a small
file called 'config' can be created in that protocol decoder's
directory, with the following content:
# comments are ok
extra-install vendorlist.txt commands.txt
|
|
|
|
|
|
This better reflects what it is: a python object generated and
processed by python code.
|
|
|
|
The usb_signalling PD should not care about packets, only symbols and bits.
The new (fixed) usb_packet PD constructs packets out of individual bits now.
|
|
Also, add missing output for some packet types.
|
|
|
|
|
