onewire: placing protocol layers into separate directories

1 files changed, 0 insertions, 78 deletions

diff --git a/decoders/onewire/__init__.py b/decoders/onewire/__init__.py
deleted file mode 100644
index 0a712ef..0000000
--- a/decoders/onewire/__init__.py
+++ /dev/null
@@ -1,78 +0,0 @@
-##
-## This file is part of the sigrok project.
-##
-## Copyright (C) 2012 Uwe Hermann <uwe@hermann-uwe.de>
-##
-## This program is free software; you can redistribute it and/or modify
-## it under the terms of the GNU General Public License as published by
-## the Free Software Foundation; either version 2 of the License, or
-## (at your option) any later version.
-##
-## This program is distributed in the hope that it will be useful,
-## but WITHOUT ANY WARRANTY; without even the implied warranty of
-## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-## GNU General Public License for more details.
-##
-## You should have received a copy of the GNU General Public License
-## along with this program; if not, write to the Free Software
-## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
-##
-
-'''
-1-Wire protocol decoder.
-
-The 1-Wire protocol enables bidirectional communication over a single wire (and
-ground) between a single master and one or multiple slaves. The protocol is
-layered, the provided parser decodes the next layers:
-- Link layer (reset, presence detection, reading/writing bits)
-- Network layer (skip, search, match device ROM addresses)
-The higher layers (transport, presentation) are not decoded, since they are
-mostly device specific and it would take a lot of code to interpret them.
-
-Sample rate:
-A high enough sample rate is required to properly detect all the elements of
-the protocol. A lower sample rate can be used if the master does not use
-overdrive communication speed. The next minimal values should be used:
-- overdrive     available:   2MHz minimum, 5MHz suggested
-- overdrive not available: 400kHz minimum, 1MHz suggested
-
-Probes:
-1-Wire requires a single signal, but some master implementations might have a
-separate signal use to deliver power to the bus during temperature conversion
-as an example. This power signal is currently not parsed.
-- owr (1-Wire bus)
-- pwr (1-Wire power)
-
-Options:
-1-Wire is an asynchronous protocol, so the decoder must know the sample rate.
-The timing for sampling bits, presence and reset is calculated by the decoder,
-but in case the user wishes to use different values, it is possible to
-configure the next timing values (number of sample rate periods):
-- overdrive              (if active the decoder will be prepared for overdrive)
-- cnt_normal_bit         (time for normal mode sample bit)
-- cnt_normal_presence    (time for normal mode sample presence)
-- cnt_normal_reset       (time for normal mode reset)
-- cnt_overdrive_bit      (time for overdrive mode sample bit)
-- cnt_overdrive_presence (time for overdrive mode sample presence)
-- cnt_overdrive_reset    (time for overdrive mode reset)
-This options should be configured only on very rare cases and the user should
-read the decoder source code to understand them correctly.
-
-Annotations:
-Annotations can be shown for each layer of the protocol separately:
-- link (the value of each transmitted bit is shown separately)
-- network (the ROM command, and address are shown)
-- transport (only transport layer byte transfers are shown)
-If link layer annotations are shown, possible issues with sample rate and sample
-timing are also shown.
-
-TODO:
-- add CRC checks for network layer
-- add transport layer code
-- review link layer code, to check for protocol correctness
-- define output protocol
-'''
-
-from .onewire_link    import *
-from .onewire_network import *
-