1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
|
-------------------------------------------------------------------------------
Agilent MSO7034A
-------------------------------------------------------------------------------
This is a set of files saved/exported from the Agilent MSO7034A oscilloscope.
Details:
http://www.keysight.com/en/pd-1293631-pn-MSO7034A/mixed-signal-oscilloscope-350-mhz-4-analog-plus-16-digital-channels
Setup
-----
The oscilloscope has the following options in the 'Save/Recall' menu, that
can be used to save the acquired/displayed data on a USB thumb drive:
- Trace and Setup
- Used to store the data *in* the scope (not on USB thumb drive)
- BMP (8-bit) image file
- Options: Setup info = y/n, Invert Grat = y/n, Palette = Color/Grayscale
- BMP (24-bit) image file
- Options: Setup info = y/n, Invert Grat = y/n, Palette = Color/Grayscale
- PNG (24-bit) image file
- Options: Setup info = y/n, Invert Grat = y/n, Palette = Color/Grayscale
- CSV data file
- Options: Setup info = y/n, Length = 100/250/500/1000
- ASCII XY data file
- Options: Setup info = y/n, Length = x
(x = 100/250/500/1000/2000/5000/10000/20000/50000/100000/200000/500000
1000000/2000000)
- ALB data file
- Options: Setup info = y/n, Length = x (see above),
Alb serial format = Default/CAN/I2C/LIN/UART|RS232/SPI2/SPI3/SPI4
- BIN data file
- Options: Setup info = y/n, Length = x (see above)
- Lister data file
- No options
When "Setup info" is enabled, the scope also saves an additional file
with the respective basename and a *.txt extention (e.g. "scope_0.txt"),
which contains some ASCII info about the scope setup, any measurements
displayed on the LCD, and so on.
Files
-----
Channels 1 and 2 of the (4-channel) scope were connected to the test output
of the scope (used for probe impedance matching), which outputs a 1.2kHz
square wave signal with an amplitude of 2.5V (2.72V peak-to-peak).
After the "Stop" button was pressed, the following files were saved:
scope_0: BMP (8-bit)
scope_1: BMP (24-bit)
scope_2: PNG (24-bit)
scope_3: CSV, 1000
scope_4: CSV, 500
scope_5: CSV, 250
scope_6: CSV, 100
scope_7: ASCII XY, 100
scope_8: ASCII XY, 250
...
scope_19: ASCII XY, 1000000
scope_20: ASCII XY, 2000000
scope_21: ALB, 100, Default
scope_22: ALB, 100, CAN
scope_23: ALB, 100, I2C
scope_24: ALB, 100, LIN
scope_25: ALB, 100, UART/RS232
scope_26: ALB, 100, SPI2 (SPI3/4 cannot be be used with only 2 channels)
scope_27: BIN, 100
scope_28: BIN, 250
scope_29: BIN, 500
scope_30: Lister
Only two "Setup info" files are included, scope_0.txt and scope_4.txt.
The first one is valid (and identical) for files scope_0* to scope_3*, the
latter is valid (and identical) for the files scope_4* to scope_30*.
The *.bin files contain the device's serial number. This has been changed
(via hex editor) to "MY12345678" in the files.
|
