1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
|
-------------------------------------------------------------------------------
JTAG / Toshiba TMPA900
-------------------------------------------------------------------------------
This is a set of example captures of JTAG communication to a Glyn Tonga2
eval board with a Toshiba TMPA900 (ARM9) microcontroller.
The JTAG adapter used was the FTDI FT2232H based Floss-JTAG (V0.2).
Details:
http://randomprojects.org/wiki/Floss-JTAG
http://randomprojects.org/wiki/Linux_on_the_Glyn_Tonga2_%28Toshiba_TMPA900,_ARM9%29#JTAG
http://www.semicon.toshiba.co.jp/openb2b/websearch/productDetails.jsp?partKey=TMPA900CMXBG
Logic analyzer setup
--------------------
The logic analyzer used was a Saleae Logic (at 4MHz):
Probe JTAG connector
--------------------------
1 (black) TRST#
2 (brown) TDI
3 (red) TMS
4 (orange) TCK
5 (yellow) TDO
6 (green) RST
7 (blue) RTCK
glyn_tonga2_init.sr
-------------------
The following OpenOCD command was used:
openocd -f interface/flossjtag-noeeprom.cfg -f board/glyn_tonga2.cfg \
-c "adapter_khz 1000" -c "init"
(this runs the OpenOCD "tonga2_init" function too, which sets up clocks/RAM)
The sigrok command line used was:
sigrok-cli -d 0:samplerate=4mhz --time 5s \
-p '1=TRST,2=TDI,3=TMS,4=TCK,5=TDO,6=RST,7=RTCK' -o <filename>
glyn_tonga2_reset.sr
--------------------
The following OpenOCD command was used:
openocd -f interface/flossjtag-noeeprom.cfg -f board/glyn_tonga2.cfg \
-c "adapter_khz 1000" -c "init" -c "halt" -c "poll off" \
-c "sleep 4000" -c "reset" -c "halt"
(only the last "reset" and "halt" are in the dump)
The sigrok command line used was:
sigrok-cli -d 0:samplerate=4mhz --time 5s \
-p '1=TRST,2=TDI,3=TMS,4=TCK,5=TDO,6=RST,7=RTCK' -o <filename>
glyn_tonga2_idle.sr
-------------------
The following OpenOCD command was used:
openocd -f interface/flossjtag-noeeprom.cfg -f board/glyn_tonga2.cfg \
-c "adapter_khz 1000" -c "init"
The sigrok command line used was:
sigrok-cli -d 0:samplerate=4mhz --time 3s \
-p '1=TRST,2=TDI,3=TMS,4=TCK,5=TDO,6=RST,7=RTCK' -o <filename>
sigrok-cli was only started a few seconds after the OpenOCD init/connection
to capture what happens when the user doesn't actively use OpenOCD commands.
glyn_tonga2_irscan_drscan.sr
----------------------------
The following OpenOCD command was used:
openocd -f interface/flossjtag-noeeprom.cfg -f board/glyn_tonga2.cfg \
-c "adapter_khz 1000" -c "init" -c "halt" -c "poll off" \
-c "sleep 4000" -c "irscan tmpa900.cpu 0xe" \
-c "drscan tmpa900.cpu 32 0"
This gets the 32bit contents of the IDCODE register (0b1110): 0x07926031.
The sigrok command line used was:
sigrok-cli -d 0:samplerate=4mhz --time 5s \
-p '1=TRST,2=TDI,3=TMS,4=TCK,5=TDO,6=RST,7=RTCK' -o <filename>
|
