Add a few OOK dumps.

11 files changed, 207 insertions, 0 deletions

diff --git a/ook/for_x_secs/README b/ook/for_x_secs/README
new file mode 100644
index 0000000..eba87a9
--- /dev/null
+++ b/ook/for_x_secs/README
@@ -0,0 +1,52 @@
+-------------------------------------------------------------------------------
+FOR X SECS: OOK data
+-------------------------------------------------------------------------------
+
+for_x_secs contains longer captures which can contain multiple signals of
+interest.
+
+
+Notes for oregon_12s.sr
+-----------------------
+
+This is a 12 second capture of 433 MHz amplitude modulated data. It contains
+traces for an Oregon Scientific THGN800 temperature and humidity sensor, a
+PCR800 rain sensor, a WGR800 wind sensor and a virtual BTHR968 temperature
+humidity and pressure sensor. There may also be some other signals in there
+too.
+
+In order to decode the Oregon v2.1 BTHR968 you will need to change the
+preamble to '1010 ...' in the ook decoder. Currently you can ook decode either
+a preamble of '1111 ...' or '1010 ...' but not both at the same time, so you
+can see Oregon v2.1 or v1/3 sensors.
+
+The signal was received by an RF Solutions RX12 superhet decoder chip and then
+passed to the logic analyser.
+
+The individual traces are also in separate files under the oregon folder.
+
+Details:
+https://www.rfsolutions.co.uk/downloads/1481732062DS-AM-RX12.pdf
+
+
+Logic analyzer setup
+--------------------
+
+The logic analyzer used was a USBee AX Pro / Saleae Logic clone (at 25kHz):
+
+  Probe       RX12
+  ----------------
+  0           OUT
+  1           Output from Arduino running virtual BTHR968
+
+
+Data
+----
+
+ * oregon_12s.sr:
+   Contains a set of pulses that include Oregon Scientific PCR800, THGN800,
+   WGR800 and BTHR968 sensors.
+
+ * one_transition_10s.sr:
+   Contains a single transition around 1 sec that is a useful template for
+   using the ook_gen decoder.
diff --git a/ook/for_x_secs/one_transition_10s.sr b/ook/for_x_secs/one_transition_10s.sr
new file mode 100644
index 0000000..b49e25f
--- /dev/null
+++ b/ook/for_x_secs/one_transition_10s.sr
diff --git a/ook/for_x_secs/oregon_12s.sr b/ook/for_x_secs/oregon_12s.sr
new file mode 100644
index 0000000..2a85513
--- /dev/null
+++ b/ook/for_x_secs/oregon_12s.sr
diff --git a/ook/oregon/bthr968/README b/ook/oregon/bthr968/README
new file mode 100644
index 0000000..cbc4ab6
--- /dev/null
+++ b/ook/oregon/bthr968/README
@@ -0,0 +1,40 @@
+-------------------------------------------------------------------------------
+BTHR968: OOK data
+-------------------------------------------------------------------------------
+
+This is an example capture of a virtual Oregon Scientific BTHR968 temperature,
+humidity and pressure sensor which transmits at 433.92 MHz using Manchester
+encoding and amplitude modulation.
+
+The signal was received by an RF Solutions RX12 superhet decoder chip and then
+passed to the logic analyser.
+
+In order to decode the Oregon v2.1 BTHR968 you will need to change the
+preamble to '1010 ...' in the ook decoder. Currently you can ook decode either
+a preamble of '1111 ...' or '1010 ...' but not both at the same time, so you
+can see Oregon v2.1 or v3 sensors.
+ 
+Details:
+https://gist.github.com/RouquinBlanc/5cb6ff88cd02e68d48ea BTHR918N_ArduinoSender.ino
+https://www.rfsolutions.co.uk/downloads/1481732062DS-AM-RX12.pdf
+
+
+Logic analyzer setup
+--------------------
+
+The logic analyzer used was a USBee AX Pro / Saleae Logic clone (at 25kHz):
+
+  Probe       RX12
+  ----------------
+  0           OUT
+  1           Output from Arduino running virtual BTHR968
+
+
+Data
+----
+
+ * oregon_bthr968.sr:
+   Contains a single set of pulses that belong to a virtual Oregon Scientific
+   BTHR968 temperature, humidity and pressure sensor. These should decode as
+   channel 2, battery OK, rollingcode BC, temp 11.2 deg C, humidity 52%,
+   pressure 1013mb, checksum OK.
diff --git a/ook/oregon/bthr968/oregon_bthr968.sr b/ook/oregon/bthr968/oregon_bthr968.sr
new file mode 100644
index 0000000..c4cc5fd
--- /dev/null
+++ b/ook/oregon/bthr968/oregon_bthr968.sr
diff --git a/ook/oregon/pcr800/README b/ook/oregon/pcr800/README
new file mode 100644
index 0000000..8ada7dd
--- /dev/null
+++ b/ook/oregon/pcr800/README
@@ -0,0 +1,38 @@
+-------------------------------------------------------------------------------
+PCR800: OOK data
+-------------------------------------------------------------------------------
+
+This is an example capture of an Oregon Scientific PCR800 rain sensor which
+transmits at 433.92 MHz using Manchester encoding and amplitude modulation.
+
+The signal was received by an RF Solutions RX12 superhet decoder chip and then
+passed to the logic analyser.
+
+In order to decode the Oregon v3 PCR800 you will need a preamble of '1111 ...'
+(default) in the ook decoder. Currently you can ook decode either a preamble
+of '1111 ...' or '1010 ...' but not both at the same time, so you can see
+Oregon v2.1 or v1/3 sensors.
+
+Details:
+http://www.oregonscientificstore.com/p-5-oregon-scientific-pcr800-wireless-rain-gauge-for-professional-weather-stations.aspx
+https://www.rfsolutions.co.uk/downloads/1481732062DS-AM-RX12.pdf
+
+
+Logic analyzer setup
+--------------------
+
+The logic analyzer used was a USBee AX Pro / Saleae Logic clone (at 25kHz):
+
+  Probe       RX12
+  ----------------
+  0           OUT
+  1           Output from Arduino running virtual BTHR968
+
+
+Data
+----
+
+ * oregon_pcr800.sr:
+   Contains a single set of pulses that belong to an Oregon Scientific PCR800
+   rain sensor. These should decode as channel 0, battery OK, rainfall 0
+   in/hour, total 38.885 inches (since the battery was changed), checksum OK.
diff --git a/ook/oregon/pcr800/oregon_pcr800.sr b/ook/oregon/pcr800/oregon_pcr800.sr
new file mode 100644
index 0000000..5b9d227
--- /dev/null
+++ b/ook/oregon/pcr800/oregon_pcr800.sr
diff --git a/ook/oregon/thgn800/README b/ook/oregon/thgn800/README
new file mode 100644
index 0000000..fd51513
--- /dev/null
+++ b/ook/oregon/thgn800/README
@@ -0,0 +1,39 @@
+-------------------------------------------------------------------------------
+THGN800: OOK data
+-------------------------------------------------------------------------------
+
+This is an example capture of an Oregon Scientific THGN800 temperature and
+humidity sensor which transmits at 433.92 MHz using Manchester encoding and
+amplitude modulation.
+
+The signal was received by an RF Solutions RX12 superhet decoder chip and then
+passed to the logic analyser.
+
+In order to decode the Oregon v3 THGN800 you will need a preamble of '1111 ...'
+(default) in the ook decoder. Currently you can ook decode either a preamble of
+'1111 ...' or '1010 ...' but not both at the same time, so you can see Oregon
+v2.1 or v1/3 sensors.
+
+Details:
+http://www.oregonscientificstore.com/p-381-oregon-scientific-thgn800-oem-wireless-temperature-humidity-sensor-for-professional-weather-stations-not-in-retail-packaging.aspx
+https://www.rfsolutions.co.uk/downloads/1481732062DS-AM-RX12.pdf
+
+
+Logic analyzer setup
+--------------------
+
+The logic analyzer used was a USBee AX Pro / Saleae Logic clone (at 25kHz):
+
+  Probe       RX12
+  ----------------
+  0           OUT
+  1           Output from Arduino running virtual BTHR968
+
+
+Data
+----
+
+ * oregon_thgn800.sr:
+   Contains a single set of pulses that belong to an Oregon Scientific THGN800
+   temperature and humidity sensor. These should decode as channel 1,
+   battery OK, rollingcode F6, temp +17.3 deg C, humidity 52%, checksum OK.
diff --git a/ook/oregon/thgn800/oregon_thgn800.sr b/ook/oregon/thgn800/oregon_thgn800.sr
new file mode 100644
index 0000000..b149122
--- /dev/null
+++ b/ook/oregon/thgn800/oregon_thgn800.sr
diff --git a/ook/oregon/wgr800/README b/ook/oregon/wgr800/README
new file mode 100644
index 0000000..cbc26fb
--- /dev/null
+++ b/ook/oregon/wgr800/README
@@ -0,0 +1,38 @@
+-------------------------------------------------------------------------------
+WGR800: OOK data
+-------------------------------------------------------------------------------
+
+This is an example capture of an Oregon Scientific WGR800 wind sensor which
+transmits at 433.92 MHz using Manchester encoding and amplitude modulation.
+
+The signal was received by an RF Solutions RX12 superhet decoder chip and then
+passed to the logic analyser.
+
+In order to decode the Oregon v3 WGR800 you will need a preamble of '1111 ...'
+(default) in the ook decoder. Currently you can ook decode either a preamble of
+'1111 ...' or '1010 ...' but not both at the same time, so you can see Oregon
+v2.1 or v1/3 sensors.
+
+Details:
+http://www.oregonscientificstore.com/p-378-oregon-scientific-wgr800-oem-professional-wind-sensor-not-in-retail-packaging.aspx
+https://www.rfsolutions.co.uk/downloads/1481732062DS-AM-RX12.pdf
+
+
+Logic analyzer setup
+--------------------
+
+The logic analyzer used was a USBee AX Pro / Saleae Logic clone (at 25kHz):
+
+  Probe       RX12
+  ----------------
+  0           OUT
+  1           Output from Arduino running virtual BTHR968
+
+
+Data
+----
+
+ * oregon_wgr800.sr:
+   Contains a single set of pulses that belong to an Oregon Scientific WGR800
+   wind sensor. These should decode as channel 0, battery OK, rollingcode 5E,
+   direction NE(45deg), gust 3.3m/s, speed 2m/s, checksum OK.
diff --git a/ook/oregon/wgr800/oregon_wgr800.sr b/ook/oregon/wgr800/oregon_wgr800.sr
new file mode 100644
index 0000000..e2d594c
--- /dev/null
+++ b/ook/oregon/wgr800/oregon_wgr800.sr