| Age | Commit message (Collapse) | Author |
|---|
|
|
|
All PDs where "trivial" self.wait() conversion was used now have this
specific comment, so it's easy to grep for.
|
|
This is managed by the backend and should be read-only for PDs.
|
|
|
|
|
|
|
|
|
|
This decoder annotates i2c traffic to indicate the type of HDCP
message contained. It includes HDCP2.2 and HDCP1.4. Useful for
analysing HDCP negotiation failures.
|
|
Also flush previously accumulated payload data when the IFC signal
asserts (interface clear, a controller requests ownership of the bus).
This is in line with EOI (end of message) and ATN (start of a command,
including change of "connected" peers or direction of communication).
|
|
When a capture contains output from a talking device, but neither
contains EOI (end of transmission) nor ATN (new commands, including
changes in the set of communicating peers or communication direction),
then lower layer data bytes would be shown but accumulated runs of upper
layer payload data would not. The hp53131a-ton.sr capture demonstrates
this behaviour.
Add transparent support for the typical case of communicating SCPI over
GPIB. Do emit upper layer payload data annotations when termination
sequences for text lines were seen. Allow users to disable this feature
when it's not appropriate for binary content.
It's an internal implementation detail that accumulated data gets flushed.
Communicate the user visible option as "payload data separation", which
should most appropriately reflect the resulting behaviour. The specific
implementation of this feature can also support different kinds of payload
chunk separation.
|
|
|
|
This can be used by frontends for decoder search features.
|
|
|
|
Introduce an 'ieee488' protocol decoder which handles both the 16 lines
parallel GPIB variant as well as the serial IEC bus variant. Which kind
of supersedes the 'gpib' and 'iec' decoders.
This implementation increases maintainability because only the extraction
of raw bytes from the parallel or serial bus is separate, and all GPIB
related command/address/data interpretation is shared. This decoder extends
the feature set of the previous versions: Visual annotations are more fine
grained (more classes, additional rows, various text lengths to maintain
usability during zoom). There is binary output for communicated data,
as well as Python output for stacked decoders. Consecutive runs of
talker data gets accumulated, and is made available in binary form as well
as text (with escapes for non-printables). The terse single-letter format
(character codes '0' to 'O' for addresses) is kept for compatibility for
those users who are accustomed to it. The implemented logic also copes
with captures of low samplerate, where edges happen to fall onto the same
sample number which at higher samplerates shall be perceived as distant
and should get processed in their respective order of appearance.
This implementation tracks the most recent configuration of "peers" (the
set of talkers and listeners). A future implementation might support the
isolation of a single conversation out of a busy chat on the bus.
Some optional support for Commodore peripherals is included (currently
limited to disk channels), while it's recommended to move this logic to
a stacked decoder if it grows more complex.
|
|
|
|
|
|
|
|
This avoids floating point number option values, which makes things
a bit easier/clearer on the command-line and also matches what other
decoders do.
Also, use numbers instead of strings for the option values.
|
|
|
|
|
|
|
|
This makes the decoder a lot nicer to use from the command-line.
* num_data_bits -> data_bits
* parity_type -> parity
* num_stop_bits -> stop_bits
* rx_packet_delimiter -> rx_packet_delim
* tx_packet_delimiter -> tx_packet_delim
|
|
Rephrase the test for the availability of at least one of several
optional input signals, and reword the corresponding error message.
|
|
The previous UART decoder implementation announced a 'check_parity'
option which took no effect (support code was missing). Remove it. Add
another 'ignore' parity choice instead, which consumes the parity bit's
position yet always passes the check.
|
|
|
|
Generally show "bits" and other smaller annotations in rows that come
before "larger" annotations (in later rows).
|
|
|
|
|
|
Do more of the calculation with floating point, only trim precision and
enforce integers at the end of the determination of the next sample
point. This shall increase robustness at low capture sample rates.
|
|
|
|
|
|
|
|
Without this, e.g. the recently added 'IDLE' ptype of the UART decoder
would cause issues.
|
|
|
|
Detect periods of a frame's length with idle level, and communicate
these time spans to stacked decoders by means of PYTHON output. Do *not*
display these idle frames in regular annotations, for backwards compat.
|
|
|
|
|
|
|
|
|
|
|
|
The gpib decoder tried to "flush" input data at a user specified sample
number when the input data lacked the respective edge which triggers the
processing during regular operation.
This is rather obscure a feature, not seen in any other decoder, perhaps
a workaround for bug #292, rather unaccessible to users (units of sample
numbers not times nor automatic detection of the EOF condition), highly
confusing according to user reports, and not covered by existing tests.
The mere presence of this option caused severe issues in application
code (see bug #1444). While there is no apparent fix that won't affect
other decoders. So let's drop this questionable feature. Valid and
complete captures should contain all relevent edges and thus decode
properly.
|
|
|
|
|
|
|
|
|
|
This is a protocol decoder for the 'ASCII' protocol used by
Amulet Technologies LCDs.
Currently some commands are not implemented yet. I also lack capture data
from a display that will use replies other than ACK and NACK.
Reads are untested as I have no suitable captures.
The PD copes with bus errors (there is an actual bug in the device I'm
reverse engineering) and most of the commands are implemented.
The unimplemented commands should generally consume the correct
number of bytes from the bus, the exception to this are the drawing
commands, because there are actually at least two revisions of them
with different payloads, that are really hard to detect in greedy
algorithm.
|
|
|
|
|
|
|
|
Similar to the recently added [rx|tx]_packet_delimiter options, these
emit summary annotations ("packets") when a certain number of data values
have been decoded.
This is a convenience feature which can be useful when a user wants to
view data which doesn't have a specified delimiter value (as last data
value in the "packet"), but rather fixed-length "packets".
This is just an (intentionally very simple) helper/convenience improvement
and is NOT meant to replace "proper" stacked decoders for UART-based protocols.
|
