| Age | Commit message (Collapse) | Author |
|---|
|
The new 'usb_signalling' and the 'usb_protocol' PD which stacks on top
of it, replace the old 'usb' decoder.
|
|
|
|
This shall support the original National LM75 I2C-based temperature sensor,
as well as various compatible devices of other vendors, such as the
Fairchild FM75, Dallas DS75, and so on.
Currently only 9bit resolution is supported, and not all commands are
decoded, yet. The register contents and temperatures are decoded
correctly though, and can be output in both Celsius and Kelvin.
|
|
Needed for g_get_monotonic_time(). Thanks to Tomaž Šolc.
|
|
The 'usb_signalling' decoder just decodes symbols from D+/D- levels,
handles bit stuffing and outputs the symbols and (potential) packets.
The 'usb_protocol' decoder takes that output and tried to parse USB
packets from it (SOF, SETUP, IN, OUT, DATA0, and so on).
This is the base decoder on top of which various others will stack
later on.
The two new PDs are work in progress, so we still keep the old 'usb' PD
around for a little while, until the two new ones are fully working and
well-tested.
|
|
This PD stacks on top of the UART protocol decoder, and ouputs the
decoded UART data in the "canonical" format, one byte after the other
without any metadata (start bits, stop bits, parity bits, errors) and
without any sample-numbers and such. This is basically what you would
see in a terminal program, such as minicom.
Per default it outputs to stdout, but using the 'filename' option
and/or the 'filename_rx'/'filename_tx' options it can also output to
files.
Using the 'tx' and 'rx' options you can also select whether both, or
only one of the data direction's data should be output.
Example:
sigrok-cli -i foo.sr \
-a uart:rx=0:tx=1,uart_dump:rx=no:tx=yes:filename=foo.txt \
-s uart,uart_dump
This PD is just an experiment for now, it's possible that it will be
replaced / reimplemented via a different sigrok facility later on.
|
|
|
|
|
|
|
|
Add ACLOCAL_DIR setting and AM_PROG_AR macro for compiling with Homebrew
under Mac OS X.
Applies essentially the same change to
{libsigrok,libsigrokdecode,sigrok-cli}/{autogen.sh,configure.ac}
It may be that the same fix is needed for the other autogen.sh and/or
configure.ac files, but that hasn't been tested and therefore not in
this commit.
|
|
(not yet finished)
This protocol decoder can decode ST STM32 specific JTAG accesses, knows
about the STM32-specific registers and bits.
|
|
This is unfinished, needs some more work.
|
|
Not quite finished yet, but relatively close.
|
|
This is unfinished and not tested, and probably not really working, yet.
|
|
|
|
|
|
No need to use the LIBSIGROKDECODE_ prefix here when we use SRD_ everywhere
else. Also, better distinction between package version and lib version.
|
|
|
|
The i2cdemux protocol decoder is the more generic version of the
obsolete ebr30a_i2c_demux decoder, and should be able (now or later) to do
everything that ebr30a_i2c_demux can do.
|
|
The next (and first) libsigrok release will be called 0.1.0.
The next (and first) libsigrokdecode release will be called 0.1.0.
The next sigrok-cli release will be called 0.3.0 (as we already had a 0.1
and 0.2 release of sigrok-cli; those did not yet use the libs, though).
sigrok-gtk and sigrok-qt didn't have any releases yet, so their version
numbers are set to 0.1.0.
Also, consistently use three numbers/digits for our version numbers.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Add missing checks and quotes, remove superfluous checks, etc.
|
|
|
|
|
|
This yields a slightly more "tidy" top-level directory.
|
|
|
|
|
|
|
|
|
