| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2012-05-23 | srd: onewire: Get optional 'pwr' probe value, too. | Uwe Hermann | |
| 2012-05-23 | srd: onewire: Drop UART leftover comments. | Uwe Hermann | |
| 2012-05-23 | removed some code copied from UART decoder, fixed some Python syntax issues | Iztok Jeras | |
| 2012-05-23 | unfinished update to onewire protocol decoder | Iztok Jeras | |
| 2012-05-23 | commiting new unfinished 1-wire decoder | Iztok Jeras | |
| 2012-05-18 | srd: MX25Lxx05D: Fix inverted SRWD bit handling. | Uwe Hermann | |
| 2012-05-18 | srd: MX25Lxx05D: Decode status register bits. | Uwe Hermann | |
| 2012-05-18 | srd: MX25Lxx05D: Fix SE command. | Uwe Hermann | |
| 2012-05-18 | srd: MX25Lxx05D: Implement READ command. | Uwe Hermann | |
| 2012-05-17 | srd: MX25Lxx05D: Implement RDSR and PP commands. | Uwe Hermann | |
| Also, some small fixes and additional debug code/output. | |||
| 2012-05-17 | srd: spi: Document output protocol, send CS# changes. | Uwe Hermann | |
| As per guidelines in HACKING, the protocol "commands"/items should be ALLCAPS, thus change 'data' to 'DATA'. Also, fix MX25Lxx05D protocol decoder accordingly, currently the only one we have which stacks on top of SPI. Add a new 'CS-CHANGE' output protocol item, which is sent upon every change of the CS# pin value (either 0->1, or vice versa). This is needed by various higher-level PDs. | |||
| 2012-05-15 | sr/srd/cli: Fix compiling with Homebrew. | Pekka Nikander | |
| Add ACLOCAL_DIR setting and AM_PROG_AR macro for compiling with Homebrew under Mac OS X. Applies essentially the same change to {libsigrok,libsigrokdecode,sigrok-cli}/{autogen.sh,configure.ac} It may be that the same fix is needed for the other autogen.sh and/or configure.ac files, but that hasn't been tested and therefore not in this commit. | |||
| 2012-05-10 | srd: JTAG: Enavble and get/use optional probes. | Uwe Hermann | |
| 2012-05-10 | srd: Support for one or more optional probes. | Uwe Hermann | |
| In the protocol decoder you always get all required probes, then _all_ optional probes in the list of probes in the decode() call. Example: (r1, r2, r3, o1, o2, o3, o4) = pins In this case r1-r3 are required probes, o1-o4 are optional probes. However, the value of valid/used/specified probes will be 0 or 1, whereas the value of probes that were not specified/assigned by the user will be (at the moment) 42. The PD can check for a valid probe like this: if p in (0, 1): ... Or check for an invalid probe: if (p > 1): ... The value of 42 could change to be -1 or None later. | |||
| 2012-05-09 | srd: Fix a few Doxygen errors. | Uwe Hermann | |
| 2012-05-09 | srd: Add usable one-liner descriptions for all PDs. | Uwe Hermann | |
| 2012-05-08 | srd: Remove TODOs from annotation format names. | Uwe Hermann | |
| Also, fix minor consistency issues, cosmetics, typos. | |||
| 2012-05-05 | srd: JTAG/SMT32: Some more improvements. | Uwe Hermann | |
| Add APB-AP register offsets/names, refactor and fix some code, handle in/out APACC/DPACC better. | |||
| 2012-05-04 | Fix bracket placing | Thomas Jarosch | |
| Make it consistent with the rest of the code Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com> | |||
| 2012-05-03 | srd: JTAG/STM32: Factor out dpacc_data_in/out. | Uwe Hermann | |
| Also, add a few code comments. | |||
| 2012-05-03 | srd: JTAG/STM32: Decode IDCODE[31:0] parts. | Uwe Hermann | |
| 2012-05-03 | srd: JTAG: Also show the bitstrings in hex (for now). | Uwe Hermann | |
| 2012-05-03 | srd: JTAG/STM32: Various improvements, fixes. | Uwe Hermann | |
| Add APACC register handling, fix DPACC handling (esp. 'A' register size), ouput a warning upon reserved DAPABORT bits being non-zero, implement preliminary state machine, add various TODOs. This is still work in progress, not yet finished or working properly. | |||
| 2012-04-29 | srd: Add initial JTAG/STM32 protocol decoder. | Uwe Hermann | |
| (not yet finished) This protocol decoder can decode ST STM32 specific JTAG accesses, knows about the STM32-specific registers and bits. | |||
| 2012-04-29 | srd: JTAG: Add some more docs. | Uwe Hermann | |
| 2012-04-29 | srd: JTAG: The TRST# (and SRST#) signals are optional. | Uwe Hermann | |
| Don't handle them for now, will do this later. | |||
| 2012-04-29 | srd: jtag: Various bugfixes. | Uwe Hermann | |
| Most importantly, both TDI and TDO are sampled at the rising TCK edge, and only upon transitions from SHIFT-DR to SHIFT-DR and SHIFT-IR to SHIFT-IR are we to save the TDI/TDO values (if I understood this correcly). Also, start out in RUN-TEST/IDLE state for now. This is useful if you have JTAG dumps which start "in the middle" somewhere, not in the TEST-LOGIC-RESET state. For full dumps, the JTAG software usually issues five TMS=1 cycles to force the JTAG state machine into TEST-LOGIC-RESET anyway, so this works fine too. | |||
| 2012-04-26 | srd: Add initial JTAG protocol decoder. | Uwe Hermann | |
| This is unfinished, needs some more work. | |||
| 2012-04-26 | srd: lpc: Minor additions/fixes. | Uwe Hermann | |
| 2012-04-21 | srd: MXC6225XU: Bugfixes, add missing bits/registers. | Uwe Hermann | |
| 2012-04-19 | srd: Initial MEMSIC MXC6225XU protocol decoder. | Uwe Hermann | |
| Not quite finished yet, but relatively close. | |||
| 2012-04-18 | Initial LPC protocol decoder implementation. | Uwe Hermann | |
| This is unfinished and not tested, and probably not really working, yet. | |||
| 2012-04-17 | srd: Initial 0.1.0 release. | Uwe Hermann | |
| 2012-04-16 | sr/srd: SR_API/SRD_API/etc. is a no-op on MinGW. | Uwe Hermann | |
| This avoids warnings on a MinGW build. The feature depends on ELF files, but MinGW/Windows uses PE files. | |||
| 2012-04-16 | srd: Quickfix for MinGW build issue. | Uwe Hermann | |
| 2012-04-15 | srd: Add functions to query srd version(s). | Uwe Hermann | |
| 2012-04-10 | sr/srd: Use/fix SR(D)_MAX_NUM_PROBES. | Uwe Hermann | |
| 2012-04-06 | srd/i2s: Added links to documentation | Joel Holdsworth | |
| 2012-04-06 | srd/i2s: Added sample-rate and bit-depth to report | Joel Holdsworth | |
| 2012-04-06 | srd/i2s: Print a warning on receiving a malformed word | Joel Holdsworth | |
| 2012-04-06 | srd/i2s: Initial implementation | Joel Holdsworth | |
| 2012-03-31 | srd: Disable 'nunchuk' PD for now, it's unfinished. | Uwe Hermann | |
| 2012-03-31 | srd: Decoders: Fix/simplify samplenum usage. | Uwe Hermann | |
| 2012-03-31 | sr/srd: Fix 'make distcheck'. | Uwe Hermann | |
| 2012-03-31 | sr/srd: Add ChangeLog to ignore list, it's generated. | Uwe Hermann | |
| 2012-03-31 | srd: Generate ChangeLog from git upon 'make dist'. | Uwe Hermann | |
| 2012-03-31 | srd: Add NEWS file. | Uwe Hermann | |
| 2012-03-31 | srd: SRD_PACKAGE_VERSION_* for consistency. | Uwe Hermann | |
| No need to use the LIBSIGROKDECODE_ prefix here when we use SRD_ everywhere else. Also, better distinction between package version and lib version. | |||
| 2012-03-28 | srd: Some more (optional) consistency renames. | Uwe Hermann | |
| 2012-03-28 | srd/cli/qt: Some more API consistency renames. | Uwe Hermann | |
 |
index : libsigrokdecode.git | |
| libsigrokdecode | ejona86@gmail.com |
| summaryrefslogtreecommitdiff |